Si4021
 
 
2
DETAILED DESCRIPTION
The Si4021 FSK transmitter is designed to cover the unlicensed
frequency bands at 433, 868, and 915 MHz. The device
facilitates compliance with FCC and ETSI requirements.
PLL
The programmable PLL synthesizer determines the operating
frequency, while preserving accuracy based on the on-chip
crystal-controlled reference oscillator. The PLLs high resolution
allows the usage of multiple channels in any of the bands. The
FSK deviation is selectable (from 30 to 210 kHz with 30 kHz
increments) to accommodate various bandwidth, data rate and
crystal tolerance requirements, and it is also highly accurate due
to the direct closed-loop modulation of the PLL. The transmitted
digital data can be sent asynchronously through the FSK pin or
over the control interface using the appropriate command.
The RF VCO in the PLL performs automatic calibration, which
requires only a few microseconds. To ensure proper operation in
the programmed frequency band, the RF VCO is automatically
calibrated upon activation of the synthesizer. If temperature or
supply voltage change significantly or operational band has
changed, VCO recalibration is recommended.. Recalibration can
be initiated at any time by switching the synthesizer off and back
on again.
RF Power Amplifier (PA)
The power amplifier has an open-collector differential output and
can directly drive a loop antenna with a programmable output
power level. An automatic antenna tuning circuit is built in to
avoid costly trimming procedures and the so-called hand effect.
The transmitters can operate in On-Off Keying (OOK) mode by
switching the power amplifier on and off. When the appropriate
control bit is set using the Power Setting Command, the FSK pin
becomes an enable input (active high) for the power amplifier.
Crystal Oscillator
The chip has a single-pin crystal oscillator circuit, which provides
a 10 MHz reference signal for the PLL. To reduce external parts
and simplify design, the crystal load capacitor is internal and
programmable. Guidelines for selecting the appropriate crystal
can be found later in this datasheet.
The   transmitters   can   supply   the   clock   signal   for   the
microcontroller, so accurate timing is possible without the need
for a second crystal. When the chip receives a Sleep Command
from the microcontroller and turns itself off, it provides several
further clock pulses (clock tail) for the microcontroller to be
able to go to idle or sleep mode. The length of the clock tail is
programmable.
Low Battery Voltage Detector
The low battery voltage detector circuit monitors the supply
voltage   and   generates   an   interrupt   if   it   falls   below   a
programmable threshold level. The detector circuit has 50 mV
hysteresis.
Wake-Up Timer
The wake-up timer has very low current consumption (1.5 糀
typical) and can be programmed from 1 ms to several days with
an accuracy of ?%.
It calibrates itself to the crystal oscillator at every startup, and
then every 30 seconds. When the oscillator is switched off, the
calibration circuit switches on the crystal oscillator only long
enough for a quick calibration (a few milliseconds) to facilitate
accurate wake-up timing. The auto calibration feature can be
disabled by setting the a bit in the Low  Battery  Detector 
Command. 
Event Handling
In order to minimize current consumption, the device supports
sleep mode. Active mode can be initiated by several wake-up
events: timeout of wake-up timer, detection of low supply
voltage, pressing any of the four push-button inputs, or through
the serial interface. The push-button inputs can be driven by a
logic signal from a microcontroller or controlled directly by
normally open switches. Pull-up resistors are integrated.
If any wake-up event occurs, the wake-up logic generates an
interrupt, which can be used to wake up the microcontroller,
effectively reducing the period the microcontroller has to be
active. The cause of the interrupt can be read out from the
transmitters by the microcontroller through the nIRQ pin.
Interface
An SPI compatible serial interface lets the user select the
operating   frequency   band   and   center   frequency   of   the
synthesizer, polarity and deviation of FSK modulation, and output
power level. Division ratio for the microcontroller clock, wake-up
timer period, and low battery detector threshold are also
programmable. Any of these auxiliary functions can be disabled
when not needed. All parameters are set to default after power-
on; the programmed values are retained during sleep mode.
EEPROM Mode
In simple applications, the on-chip digital controller provides the
transmitters with direct interface to a serial (SPI) EEPROM. In this
case, no external microcontroller is necessary. Wake-up events
initiate automatic readout of the assigned command sequence
from EEPROM memory. For every event, there is a dedicated
starting address available in the EEPROM.
Programming the EEPROM is very simple. Any control command
can be programmed in the EEPROM sequentially (same as in
microcontroller mode).
The internal power-on reset (POR) is a dedicated event, which
can be used to program the basic settings of the transmitters. In
this case the chip starts to read out the preprogrammed data
from the 00h address in EEPROM. Data can be transmitted with
the help of the Data  Transmit  Command, which tells the
transmitters how many bytes must be transmitted. The whole
process finishes with a Sleep Command. 
 
相关PDF资料
SI4022-A0-FT IC TX FSK UNI 868/915MHZ 16TSSOP
SI4711-B30-GM IC TX FM RADIO 76-108MHZ 20UQFN
SI4713-B30-GMR IC TX FM RADIO RPS/RDS 20UQFN
SKY12146-321LF IC VAR VOLT ATTEN 12QFN
SN171GG-NR SNAP PROTOBOARD W/NO RADIO
SWLP.2450.12.4.B.02 ANTENNA WI-FI WLAN 2.4GHZ
TD4A SENSOR RTD LIQUID TEMP 2TERM
TD5A SENSOR RTD TEMP MINI 3LEAD
相关代理商/技术参数
SI4021-A1-FTR 功能描述:射频发射器 Transmitter EZRadio RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
SI-40222 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:SI-40222
SI-40223 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:SI-40223
SI-40227 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:SI-40227
SI-40228 制造商:Bel Fuse 功能描述:CONN RJ-45 RCP 32 POS 2.54MM SLDR RA TH 48TERM 4PORT - Trays
SI-40229 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:SI-40229
Si4022-A0-FT 功能描述:射频发射器 Transmitters IA4222 RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel
SI4022-A0-FTR 功能描述:射频发射器 Transmitter EZRadio RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel